Home Products AirDMX About Applications Guides Contact
eileen@sdj-lighting.com
+86 138 1968 9970 (WeChat / WhatsApp)

AirDMX · W-DMX · CRMX · RF remote

Control the rig without a cable in the room.

Every Smart Series fixture carries a wireless DMX-512 receiver on the board. AirDMX is our own name for that link. Feed it from a console through an AirBox or a battery-powered SmartBox, hand it to a 433 MHz RF remote, or leave the console in the case and run the whole rig from the AirApp.

How the signal travels

Two radios and one box. Nothing else in the chain changes.

01

Console out

A DMX-512 desk feeds the AirBox on an ordinary data cable — the last cable in the room.

02

On the air

The AirBox transmits on 2.4 GHz. Fixtures keep the addresses and channel maps you already patched.

03

Fixture in

Each fixture receives, decodes and drives its own LEDs. Sixteen ID groups keep neighbouring rigs apart.

DMX CONSOLE AIRBOX NEO 6 ENZO 18 DMX-512 OUT OWN ANTENNAS, ON BOARD UPLIGHT · 6 × 20W WASH · 18 × 20W DMX CABLE 2.4 GHz
Console → AirBox → fixtures. The only cable left is the one at front of house.

Four ways to run it

A programmed show, one fixture leading the rest, a handset, or a phone.

Console + AirBox

DMX as you patched it

Any DMX-512 desk drives the AirBox. Addresses stay as they were patched, so cues, chases and theatre-style plotting run exactly as written.

Master / slave

One fixture leads

Set a single fixture as master and it broadcasts its built-in program to the rest of the chain. No console, no phone, no operator.

RF remote · 433 MHz

Four IDs, no aiming

A 433 MHz handset replaces the old infrared remote: four group IDs, control through a crowd, and no need to point at a receiver on the fixture.

AirApp

A phone does the job

With the AirBox in WiFi hub mode, the free AirApp on iOS or Android sends colour, intensity and programs to the whole rig.

RF remote — a handset, not a console

433 MHz, four group IDs, twelve keys, no aiming. It changes the scene; the fixture keeps running the look.

433 MHz RF remote handset for battery powered wireless DMX LED par lights, four group IDs, no line of sight
Four groups on one table: the handset changes the scene, the fixtures run it.

A pocket-sized RF handset that sends a short command on 433 MHz; the fixture receives it and runs a program of its own. It is not a console and it does not carry DMX data — which is exactly why it works with a coin cell and why it keeps working when the remote is back in your pocket.

That matters in the room. Infrared has to see the receiver window on the fixture, and stage light, sunlight or someone walking through the beam will break the shot. This one does not need to be pointed anywhere: 433 MHz bends around people, flight cases and truss.

Band433.92 MHz Groups4 IDs RangeUp to 100 m Keys12

Groups

Four IDs, one touch

Four groups of fixtures, one key to step between them. Hold GROUP for two seconds and every group answers — light a room in zones without re-pairing anything.

Aiming

No line of sight needed

Face away, keep it in a pocket, shoot through a flight case. There is no receiver window to find and no aiming to do.

Range

Further than infrared

Up to 100 m in the open, on a clear line of sight — 30 m in a crowded rig with truss and bodies in the way. Strong stage light does not wash the command out.

Two bands

Nothing to interfere with

The handset talks on 433 MHz while wireless DMX stays on 2.4 GHz. The two bands sit about 2 GHz apart, so the remote never competes with the console link.

Signature key · Frost

One key, the diffusion layer

Cycles the Frost Glass layer — fog, semi, clear, dynamic — without going into a menu. No other handset on the market reaches it directly.

Signature key · PSM

One key, the run-time mode

MAX / STD / ECO on a single key, so a long evening can be traded for output on the spot rather than at the menu.

A table moves, the cake comes in, the speeches start — the room changes and the lighting has to follow it in the next four seconds, not at the next sound check.

That is the whole job of this handset: no laptop, no console, no dongle, no aiming. If a group is dim, press GROUP until its LED comes up, then BRI. If you need the room dark for a moment, press the power ring once and press it again to bring the look back exactly where it was.

It is an optional accessory for every Smart Series fixture — quoted with the rig, not as a separate system.

RF remote handset for battery powered wireless DMX par lights, in the hand at a live event, controlling four group IDs
Blackout, group change, level — all from where you are standing.

Twelve keys, one icon each

Two columns, six rows, and no + or − anywhere on the handset. One action per key.

KeyIconNameFunction
K01⏻ power ringPOWER / BOBlackout; hold 2 s for standby or wake
K022 × 2 dotsGROUP1 → 2 → 3 → 4; hold 2 s for ALL
K03☀ sunBRI +Brightness up, 16 steps, repeats on hold
K04☾ moonBRI −Brightness down, 16 steps, repeats on hold
K05» double arrowSPEED +Program speed up, repeats on hold
K06⏳ hourglassSPEED −Program speed down, repeats on hold
K07◀ trianglePREVPrevious item in the current family
K08▶ triangleNEXTNext item in the current family
K09◐ half-filled circleFROSTFog → semi → clear → dynamic
K10♪ noteSOUNDSound active on / off
K11▤ battery cellPSMMAX → STD → ECO
K12▦ 3 × 3 dotsMODEFIXED / WHITE / AUTO / MANUAL — sets what PREV and NEXT scroll
RF remote handset for battery wireless DMX lights: twelve keys, four group LEDs, 6.5 mm body
Two columns, six rows, four group LEDs on the top edge.

K12 decides which table the two arrow keys walk through: twelve fixed colours, ten white presets from 1500 K to 10000 K, three auto programs, or manual six-colour mixing.

FROST and SOUND sit outside those families, so they answer on any table. DMX address, wireless linking, language and screen settings deliberately stay on the fixture panel — a handset that can break a patched rig mid-show is a liability, not a feature.

Band433.92 MHz (433.05–434.79 MHz)
Transmit power≤ 10 mW e.r.p
Occupied bandwidth≤ 400 kHz
ModulationOOK / ASK short command packets
RangeUp to 100 m in the open, line of sight · typically 50 m · 30 m in a crowded rig
Groups4 group IDs (hold GROUP 2 s for ALL)
AimingNo line of sight required
PowerCR2032 coin cell
SizeApprox. 85 × 50 × 6.5 mm
Keys12 keys, 2 × 6, plus four group LEDs
In the fixture433 MHz receiver built in, running alongside the 2.4 GHz wireless DMX link

The remote sends a command, not a data stream. Once the fixture has the command it keeps running the program by itself, which is why the handset stops transmitting after a few milliseconds and why a coin cell lasts.

Groups on the handset are four; the sixteen ID groups belong to the wireless DMX link on the fixtures and are set from the console side. The two numbering systems are separate on purpose.

Radio compliance. This device is a short-range low-power radio transmitter compliant with the 433.05–434.79 MHz "General Wireless Remote Control" category (≤10 mW e.r.p, occupied bandwidth ≤400 kHz) and uses a fixed integral antenna which must not be replaced. Do not modify the operating scenario, extend the frequency range, increase transmit power (including adding an RF power amplifier), or change the antenna. It must not cause harmful interference to licensed radio stations and is not entitled to protection from such interference. It must accept interference from ISM equipment and other licensed stations. If harmful interference occurs, stop operation immediately and resume only after the interference is eliminated.

本产品为微功率短距离无线电发射设备,符合《微功率短距离无线电发射设备目录和技术要求》中「通用无线遥控设备」433.05–434.79 MHz 条款(发射功率限值 10 mW e.r.p,占用带宽不大于 400 kHz),采用一体化固定天线,不得擅自更换。(一)符合上述具体条款和使用场景,采用的天线类型和性能、控制与开关使用方法见本产品说明书;(二)不得擅自改变使用场景或使用条件、扩大发射频率范围、加大发射功率(包括额外加装射频功率放大器),不得擅自更改发射天线;(三)不得对其他合法的无线电台(站)产生有害干扰,也不得提出免受有害干扰保护;(四)应当承受工业、科学及医疗(ISM)应用设备或其他合法无线电台(站)的干扰;(五)如对其他合法的无线电台(站)产生有害干扰时,应立即停止使用,并采取措施消除干扰后方可继续使用。

Compatible with the transmitters you already own

AirDMX runs the rig on its own. If your company already standardised on W-DMX or CRMX, the same module is supplied in that mode.

Standard

AirDMX

Our own 2.4 GHz wireless DMX-512. Built into every fixture and every AirBox; sixteen ID groups, no licence, no extra hardware.

On request

W-DMX G3 / G4 / G4S

Wireless Solution compatible mode, for rental houses and venues already running W-DMX transmitters. Quoted per order; function and price differ by option.

On request

LumenRadio CRMX

CRMX mode for rigs built around LumenRadio. Available as a receiver option, and as a Timo FX module on the ENZO 18.

Tell us which transmitter you already own and we quote the matching receiver. The light engine, battery and IP65 housing are identical whichever mode you take.

AirApp — the console in a pocket

Free on iOS and Android. No licence, no dongle, no hardware beyond the radio already inside the fixture.

Virtual colour palette

Pick a colour on screen and every fixture follows — no gel, no re-patch.

Virtual dimmer

Intensity per fixture or per group, dragged on the phone during the event.

Colour change & fade

Built-in programs for slow colour change and fades between looks.

Sound active

Programs that follow the music when nobody is at the controls.

ProtocolDMX-512 carried over 2.4 GHz wireless
In the fixtureReceiver built into the control board of every Smart Series model
CompatibilityAirDMX standard; W-DMX G3 / G4 / G4S and LumenRadio CRMX on request
Pairing16 ID groups — several rigs can share a venue without crossing
HandsetRF remote, four group IDs, no line of sight required
AirBoxDMX input · 2.4 GHz WiFi module · two external antennas
Light engine16-bit dimming · 25,000 Hz refresh · four dimming modes · over-temperature protection
AppAirApp, free for iOS and Android

A wireless link is only worth having if the light still looks right. The 25,000 Hz refresh keeps fixtures clean on camera, 16-bit dimming holds the bottom of the curve where battery fixtures spend their evening, and the four dimming modes match the response to the room.

Radio and light engine are designed together: the receiver sits on the same board as the driver, so a fixture is either addressed or it is not — there is no separate box to lose, charge or cable.

Wireless DMX questions

The three that come up in every OEM and rental conversation.

Does AirDMX work with W-DMX or LumenRadio CRMX?

AirDMX is our own name for the 2.4 GHz wireless DMX-512 built into every fixture. The same radio module can be supplied in W-DMX G3 / G4 / G4S or LumenRadio CRMX mode on request, so fixtures drop into a rig already built around those transmitters. Function and price differ by option — tell us which transmitter you own and we quote the matching receiver.

Can I drive these fixtures from my existing DMX console?

Yes. An AirBox takes a standard DMX-512 feed on an ordinary data cable and puts it on the air; the fixtures keep the addresses and channel maps you already patched, so cues and chases run as written.

What if there is no console on site?

An RF remote controls four group IDs with no console and no AirBox in the chain — and unlike infrared it does not need to be pointed at a receiver on the fixture. With an AirBox in WiFi hub mode, the free AirApp does the same job from a phone.

Does the RF remote carry DMX?

No. It sends a short command on 433.92 MHz and the fixture then runs its own built-in program, so the look continues after the press — which is why a coin cell is enough. Wireless DMX-512 stays on 2.4 GHz and is not touched by the handset.

How far does the RF remote reach?

Up to 100 m in the open on a clear line of sight, typically 50 m, and about 30 m in a crowded rig with truss and people in the way. It never needs to be pointed at the fixture.